Motorcycle Throttle Not Snapping Back

September 16, 2021 Posting Komentar

Why would the throttle when rolled not snap back to the original position - Answered by a verified Motorcycle Mechanic We use cookies to give you the best possible experience on our website. The cables dont seem to be snagging on anything.

How To Adjust Throttle Cable Slack On Motorcycle Youtube

Thats the best way I can describe it.

Motorcycle throttle not snapping back. Loosened the bar ends a hair and it went back to normal. If you have a frayed cable you will never get it to work correctly so check the cables. I did not take the carbs off for the valve adjustment.

You need to pull the throttle tube off your bar end and clean it out. Austin L Registered. Then apply a thin even coat of white lithium grease to the inside of the throttle sleeve.

Smacked the plastic bar ends in a little harder than I should have with a rubber mallet after installing a throttle ring. Im also looking at possibly replacing the. When I roll the throttle back it stays there.

Adjust and operate the throttle again until it snaps back quickly. So after the newness of the bike has worn off I realized that the throttle doesnt snap back on the handle bar like it should. Throttle not snapping back.

If that doesnt work you may have a fray in your cable somewhere. If thats not it check the cable by the throttle body on the return end and make sure it springs back whens loosened at the grip. Discussion Starter 1 Nov 10 2019.

Could the carbs be gummed up or something. When I installed my Iso grips on my Ultra Classic I noticed that if I moved the switch housing and grip too far up on the handle bar the throttle would rub a bit and not snap back. Throttle and release again and it should snap back as quickly as before.

It feels kinda rough when I twist the. Make sure the tube isnt smashed against the end of your bar either. Have you had a tipoverwreck recently.

Thats why Im confused. This job must be done correctly. So then a friend and I checked the old cables one of them appeared to be warped the close cable so we replaced both cables that came in a pair.

Ok when I twist the throttle back it stays i tried adjusting it but it doesnt help. The bike has been sitting for about two weeks. Clean out the inside of the sleeve and the handlebars good.

If theyre adjusted too tight the throttle will stick. The throttle grip must work correctly or serious injury or death may result. Hello Been working on my bike for while ive restored alot of the bike and just working out a few kinks as the bike sat for a long time its a 1978 honda CB400 Hawk II My issue is with the.

Maybe this is an entire problem on its own. Currently putting one together. If not the return cable is too tight.

On my old bike I had to adjust the cable tension to get the throttle to snap back correctly. I tried to adjust the cables and it still doesnt snap back. With the engine off twist the throttle to wide open throttle and let go of the throttle grip.

Quick video taken on my phone about an issue on my 1981 Kz550 LTD. I made sure the bar was smooth and lubed still wont snap back. Jump to Latest Follow 1 - 7 of 7 Posts.

Well it was a PITA but I got it except that now my throttle wont snap back. If not loosen the cables a bit or back the throttle grip a bit further off the handlebars. Joined Oct 13 2019 8 Posts.

Now instead of the throttle snapping immediately back to closed position upon release it returns slowly. Put the switch housing back together and the throttle wont snap back. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.

Throttle cable very stiff and sticky does not snap back. I finally pulled my old grips and replaced them with Avon custom contour grips. My bike is fly by wire so there are no throttle cables.

I have the airbox off and am looking at the 4 carbs Please if anyone can tell me how to adjust the throttle pull back cable it would make my day so much better. Its not difficult. If that doesnt work youll have to take the throttle sleeve back off the handlebars.

The throttle snapped back. The cable that is actually activating the throttle is working just fine but its not snapping it back. As in when i let go of the throttle it does not snap back and it sticks in whatever position i put it in.

To tighten a cable you want to effectively increase the length of housing between the 2 fixed points that hold the housing in place. Throttle not snapping back. The adjustment for the cables seemed to be fine before I did the valve adjustment.

The throttle should snap shut. Dumb question how do I just the throttle cables so my throttle snaps back I changed the grips and now the throttle is not snapping back to place. Im not sure if the cable has been replaced or not but Im gonna say that it hasnt been replaced.

Posted by Anonymous on Apr 13 2013. I just bought an FZR 600 and have been working the kinks out of it one of them being the throttle sticking when i rev it almost like a cruise control. Joined Apr 11 2011 42 Posts.

I installed new grips on my bike and now the throttle does not snap back to the idle position when I let go of the - Answered by a verified Motorcycle Mechanic. Check each cable for free movement. Jump to Latest Follow 1 - 5 of 5 Posts.

Put the cable back in place and screwed it back up. You need to take the entire throttle control assembly off the handlebars and disconnect the cables from the carburetor. We use cookies to give you the best possible experience on our website.

By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. The throttle cables are in the right. What could be causing this.

Tried different combinations of loosening one cable tightening another and vice versa. Still the throttle closes slowly. Discussion Starter 1 May 8 2011.

If the cable is frayed replace it right now or sure enough it will break at the greatest distance from your truck. FYI the bike is not cranked. I thought that it would be okay to ride without the throttle snapping shut however even when the bike is running and I close the throttle it takes maybe around 5 seconds for the revs to even begin coming back down.

How To Adjust And Replace Your Motorcycle S Throttle Cable